P5 Multi-sensor device combines five MySpool devices: Power Failure, Internet Outage, Water Detectors, Temperature, and Short (DIY1) Alerts.

• A text message, email, or push notification is sent when the A/C power goes off, the internet fails, or water is detected. An email or push notification is sent when the temperature sensor exceeds set thresholds or a short condition is detected. 

  P5 added four more configuration sensors to notify when the alert condition is reverted. So, another text message, email, or push notification is sent when the A/C power is restored, the internet service is back up, or water is no longer detected. An email is sent when the Short condition no longer applies.

• All alerts, including Power ON and Power OFF, Internet ON and Internet OFF, Water ON and Water OFF, Temperature, and Short ON and Short OFF, are configured independently; each can be disabled if desired. 
• The P5 Multi-sensor is equipped with both visual and audio indicators: Red, Blue, and Green LEDs indicate Alarm, Communications, and Running conditions, respectively. An audio tone sounds to indicate an alarm condition for all alarms except for Power OFF to conserve internal batteries. The audible tone can be disabled if desired.
• The Short sensor of P5 comes with a 2-pin JST connector, which can be a simple cable for a continuity test (included), a float sensor, a push switch, or a door-open sensor, all available on MySpool.
• The high-quality waterproof temperature sensor can be operated in two modes.  One mode sends alerts when the temperature goes above or below your thresholds. The second mode allows you to send data to a ThingSpeak channel for display and analysis. See here for directions on how to set up this free data channel.
• Name each device and customize your message notifications to identify the location where an issue is detected.
• Every MySpool device is independent; no hub is required. There are no fees or subscription costs.

Note: Power, Internet ON and OFF alerts, and Water alerts can be sent as text messages, emails, push bullets, or any combination of the three. Temperature and Short alerts are sent only as email or push bullet notifications. However, you can convert one or more of the email notifications into text messages; see here for instructions.

Float, Door, and Push button sensors can be plugged in the Short sensor connector. They are NOT INCLUDED and must be purchased separately.

Be alerted away from home or business 
MySpool P5 Multi-sensor is a smart device that sends an alert when power failure is detected and when an internet outage occurs.  It also sends an alert when power or the internet comes back on. That alert is a message, either via email, text, or both. 

No Hub Required 
Each P5 Multi-sensor works independently with your Wi-Fi network. Multiple devices can be placed in different locations throughout your home or business. Your notifications will include your text for each device that you specify in the device configuration.

No Fees 
There are no fees for using MySpool P5 Multi-sensor for notifications. P5 Multi-sensors purchased on MySpool.com support 1 telephone number and up to 5 email addresses for alert notifications. See these directions to add more telephone numbers without fees.

Flexible design 
MySpool P5 Multi-sensor will ignore short-duration power fluctuations of less than 2 seconds so that no unnecessary notifications are sent. Note that since no device can send more than one alert per minute, your POWER ON notification may be delayed by up to 1 minute if power comes back on immediately. Each device requires 3 AAA batteries, which are included. The batteries should last 5 years or more, assuming average power outages and fluctuations.

The Internet detection service sends multiple status updates to MySpool cloud service per minute. The service sends an Internet OFF alert if two or more are missed. It usually takes 1-3 minutes for this alert to be generated and delivered. Once internet connectivity is restored, an Internet ON alert is sent.

Temperature sensor alerts when the temperature goes above or below your thresholds. The high-quality waterproof temperature sensor has a temperature range from -55°C to +125°C (-67°F to +257°F), with an accuracy of 0.5°C over the recommended range of -10°C to +85°C. All readings outside this range are ignored: -30°C to +105°C or -22°F to +221°F.

The water sensor alerts you when moisture is sensed by the pad, which has a 5-foot cable for flexible deployment. 

All MySpool services are free.